MY 87 VORTEX

Forum for Subaru XT and/or XT6 owners

Moderators: Hocrest, Myxalplyx, Huck369, Moodybluesr, grossgary, john in KY, SUBBYRU89, austinXT6

Re: MY 87 VORTEX

Postby Myxalplyx on Sun Dec 17, 2017 6:46 pm

What's up with all the photos? Can't see anything from photobucket.
Kevin Thomas
1989 2.7ltr XT6 AWD/Auto *WndCttr*
JC Sports Intake, Rallispec Header, Custom 2.5" exhaust with 2.5" Magnaflow muffler
Advanced Timing 32 degrees
ProECM Lightweight pulley
4.44 gears, LSD
User avatar
Myxalplyx
Moderator
 
Posts: 2763
Joined: Thu Jul 11, 2002 8:55 pm
Location: New Castle, DE

Re: MY 87 VORTEX

Postby john in KY on Sun Dec 17, 2017 8:24 pm

No problem here seeing the photos.
john in KY
Moderator
 
Posts: 3154
Joined: Tue Jul 16, 2002 8:12 pm
Location: KY

Re: MY 87 VORTEX

Postby Myxalplyx on Mon Dec 18, 2017 7:02 am

john in KY wrote:No problem here seeing the photos.


It was a work issue! I can see them ok from home. :oops:
Kevin Thomas
1989 2.7ltr XT6 AWD/Auto *WndCttr*
JC Sports Intake, Rallispec Header, Custom 2.5" exhaust with 2.5" Magnaflow muffler
Advanced Timing 32 degrees
ProECM Lightweight pulley
4.44 gears, LSD
User avatar
Myxalplyx
Moderator
 
Posts: 2763
Joined: Thu Jul 11, 2002 8:55 pm
Location: New Castle, DE

Re: MY 87 VORTEX

Postby Huck369 on Wed Jan 10, 2018 7:14 am

I was thinking the Air Suspension computer was under the drivers seat (in the US)
I've never had a spider EA18 intake, but there is usually a water line into and out of the throttle body on most Subarus to keep it from icing up in cold weather......maybe the case here?
Huck
Subaru Ambassador
88 XT6 5-Speed(Project Car)
08 Impreza 2.5I 5-Speed
92 SVX LS-Tour (Yellow AWD 5-Speed)
09 Forester X Premium
The Creator of FrankenWedge
User avatar
Huck369
Moderator
 
Posts: 15542
Joined: Tue Oct 01, 2002 9:34 am
Location: Somerset, KY

Re: MY 87 VORTEX

Postby Johnny T on Sun Feb 04, 2018 12:29 am

Hi everyone

Just an update. I have tried to install the rear breaks from the XT6 and came across a bit of a problem with connecting the break caliper to the backing plate. The issue I have is that the backing plate from the XT4 is to small for the XT6 Caliper on as the backing plate bolt holes for the calipers are 15mm too small. Is there anywhere I can get a set of XT6 backing plates sent over to Australia or would another backing plate from an older impreza fit? Worst case I will have to find a fabricator and get it custom adjusted.

The other issue I have that I will be removing the engine from my black Vortex and trying to find in the service manuals on the instructions on what I need to do. I have opened "1988 Service Manual Section 2 & 3" Section 2.11 and not getting much help as the note for engine removal only states the removal for the er27 engine and not the ea82, would the steps still be the same as the XT6 Engine? Also can anyone direct me on to what page in the service booklet I need to look up so I can get the engine and gearbox out correctly?

Thanks again everyone for all the advice :)
1987 Subaru Vortex XT Turbo 4wd 88kw of FUN!
Custom black interior and a now running ea82t engine, new front lip spoiler, rear spoiler, XT6 Hubs
Image
Johnny T
 
Posts: 217
Joined: Sat May 15, 2010 9:10 pm
Location: Australia Melbourne

Re: MY 87 VORTEX

Postby Huck369 on Mon Feb 05, 2018 12:15 pm

Pulling the EA82 out should be the same as pulling out a ER27, all the major stuff is the same, if it is a EA82T then the turbo stuff will make it a little different, but still mostly the same.
Huck
Subaru Ambassador
88 XT6 5-Speed(Project Car)
08 Impreza 2.5I 5-Speed
92 SVX LS-Tour (Yellow AWD 5-Speed)
09 Forester X Premium
The Creator of FrankenWedge
User avatar
Huck369
Moderator
 
Posts: 15542
Joined: Tue Oct 01, 2002 9:34 am
Location: Somerset, KY

Re: MY 87 VORTEX

Postby john in KY on Tue Feb 06, 2018 9:46 pm

I seem to recall years ago someone used backing plates from a Legacy. Had to be slightly modified.

Once parted out an XT6, body was too rusted out, by just unbolting the 4 engine cradle bolts and probably less than 8 other bolts and just lifted the body from the engine/transmission.
john in KY
Moderator
 
Posts: 3154
Joined: Tue Jul 16, 2002 8:12 pm
Location: KY

Re: MY 87 VORTEX

Postby Johnny T on Sun May 20, 2018 9:52 pm

Hi everyone, just a small update.

I am picking up my backing plates tomorrow night (got them laser cut to fit the rear hubs) and just trying to find where to buy a new set of disc (front and rear) for when they can't be used as I have them machined and was told they will last for another 20,000k - 30,000k before I need to find replacements. Would anyone know where I can get a set of XT6 brake discs?

Thanks again and more photos to come shortly in the next few weeks :)
1987 Subaru Vortex XT Turbo 4wd 88kw of FUN!
Custom black interior and a now running ea82t engine, new front lip spoiler, rear spoiler, XT6 Hubs
Image
Johnny T
 
Posts: 217
Joined: Sat May 15, 2010 9:10 pm
Location: Australia Melbourne

Previous

Return to Subaru XT discussions

Who is online

Users browsing this forum: Majestic-12 [Bot] and 2 guests

cron